Tamboura or Tanpura Stringing Diagrams. Below is\u00a0\u00a0Fig 1 shows the anchoring mechanism for the stings of all tambouras. The string is passed up through the hole in the tail piece, and a one half inch hook is made. The rest of the string is folded up over the bridge. The hook is clipped over the string and the hook is then pushed down into the same hole, which pinches the string down–Fig.2<\/span><\/p>\n The string is threaded twice through the hole in the shaft of the peg, and a tail of about 3\/8ths of an inch is folded down as shown–Fig. 3. The windings of the string wrap around the shaft and over the tail to prevent slippage–Fig. 4.<\/span><\/p>\n Tamboura Tuning.<\/span><\/b> Below are the Indian Sargam equivalents to European Solfege<\/span> There are roughly four sizes of tamboura: Male, Female, Tenor, and Instrumental. Sizes vary considerably between makers.<\/span><\/p>\n Male Tamboura<\/b>\u00a039″ scale length ( largest ) – tunes to A# ~ D lower octave Female Tamboura\u00a0<\/b>33″ scale length\u00a0 – tunes to G ~ A# upper octave<\/span> Tenor Tamboura<\/b>\u00a030″ scale length tunes D to G between male and female Instrumental Tamboura<\/b>\u00a026″ scale length ( smallest ) – tunes to B ~ C# upper octave The distinctive tone of a tamboura comes from the curved horn or bone bridge called the Jawari. The fine adjustment of the Jawari tone is done by sliding doubled over cotton threads under the strings. These threads can be moved back and forth until the desired amount of Jawari is achieved. We use standard cotton sewing thread. Sometimes you will need to double it again to four strands to get the desired sound.<\/span><\/p>\n <\/p>\n","protected":false},"excerpt":{"rendered":" Tamboura or Tanpura Stringing Diagrams. Below is\u00a0\u00a0Fig 1 shows the anchoring mechanism for the stings of all tambouras. The string is passed up through the hole in the tail piece, and a one half inch hook is made. The rest of the string is folded up over the bridge. The hook is clipped over … Continue reading Tamboura Tuning<\/span>
\n<\/span><\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n![\"\"](\"..\/..\/images\/tambourastring2.jpg\")
\u00a0![\"\"](\"..\/..\/images\/tambourastring1.gif\")
<\/span><\/p>\n![\"\"](\"\/images\/tambourapeg.jpg\")
\u00a0<\/span>![\"\"](\"..\/..\/images\/tambourapeg1.jpg\")
<\/span><\/span><\/a><\/span><\/p>\n
\nThe actual pitch for a tamboura depends on: The size of the tamboura, the gauge of the strings, and finally the desired pitch for your singing voice. The tuning range of any tamboura can be varied by using heavier or lighter strings.
\n<\/span><\/span><\/p>\n\n\n
\n \n
\nSa = Do
\nRe = Re,
\nGa = Mi,
\nMa = Fa,
\nPa = Sol,
\nDha = La,
\nNi =Ti,
\nSa = Do<\/span><\/span><\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\nString gauges: 1st. string Pa .022″ phos. bronze, 2nd and 3rd string Sa .020″ steel, 4th string low Sa .028″ phos bronze.<\/span><\/p>\n
\n String gauges: 1st. string Pa .014″ steel, 2nd and 3rd string Sa .012″ steel, 4th string low Sa .022″ phos bronze.<\/span><\/p>\n
\nString gauges: 1st. string Pa .015″ steel, 2nd and 3rd string Sa .013″ steel, 4th string low Sa .025″ phos bronze.<\/span><\/span><\/p>\n
\nString gauges: 1st. string Pa .014″ steel, 2nd and 3rd string Sa .012″ steel, 4th string low Sa .022″ phos bronze.
\n( The above string gauges are for standard tuning. All string gauges are in thousandths of an inch. )<\/p>\n![\"\"](\"..\/..\/images\/Jawari_Threads.jpg\")
<\/a><\/span><\/p>\n